PROJECT FOR SALE!!! - Note Price Reduction!
Pegazair-100 STOL : All metal with fabric covered fuselage is ready for instruments and 100hp engine. Built to plans with exceptional build quality. Replacement parts cost (unassembled) over $30,000 USD.
MDRA Pre-cover inspection was done in June 2011. Asking $15,000 USD. (Was $18,000)
Please contact Clarence for more information at (519) 742-3159 or cemartens at rogers.com
MDRA Pre-cover inspection was done in June 2011. Asking $15,000 USD. (Was $18,000)
Please contact Clarence for more information at (519) 742-3159 or cemartens at rogers.com
PARTS FOR SALE...Altimeter 3.5 in
Airspeed 3.5 in Vertical speed 3.5 in Turn coordinator 3.5 in Transponder & encoder Cleveland Brakes & 600 x 6 wheels & tires Tach 12 volt 2.25 in Oil temp 12 volt 2.26 in Oil pressure 12 volt 2.25 in CHT 12 volt 2.25 in EGT 12 volt 2.25 in 2Fuel level 12 volt 2.25 in Flight line 760 com radio 2.25 in Throttle mixture carb heat & other cables Lycoming O 320 E2D engine with carb mags altinator starter oil cooler and baffles Exhaust pipes and heater muffs CONTACT: Bob Schauber for prices and/or details at (519) 504-5951 or schauber@rogers.com |
|
AWARDS AND NOMINATIONS
Each year the following awards are presented to the KWRAA members who best exemplify the characteristics shown on each of the plaques. Members are asked to submit the names of other members who are deserving of these awards so they can be recognized at the annual Christmas banquet.
Congratulations to Roger Deming and Ed Welfred who were the 2018 winners of the Holy Golly and Larry Edwards awards for their contributions to KWRAA.
Please submit nominations for 2019 to Dan Oldridge by October 5, 2019 for committee review.
High Resolution Photos
| colours.jpg |
| dscn4229cfdep_glendalelr.jpg |
KWRAA Linked Files
| passenger_safety_briefing_card.pdf |
| edenvale_gathering_of_the_classics.pdf |
| ndt_-_perfection_inspection_-_ndt.jpg |
| sound_new_private_waterloo.pdf |
| private_app_fillable_sound.pdf |
KWRAA TOOL CRIB (Available to chapter members on a short-term loan basis)
20" Rivet Punch Tool
Spray Gun Cleaning Kit
AN & Mil. Spec Hardware (in 42 drawer cabinet)
Clecoes (3/32, 1/8, 5/32, 3/16, 7/32, 1/4 inch)
Greenlee Panel Punch for 2.25 and 3.125 in.
Screw Driver Set with Security Bits
Hollow Punch Set
Rivet Dies, Dimpler and Countersink
Counter Sink Gauges, Centre Punch, Deburr
Drill Stops (9)
Right Angle Drill Guide plus Screw Bits
Plexiglass Drill Bits
Pipe Vice with Bench Clamp
9 Piece Super-Thin Wrench Set - Imperial & Metric
2 Joint Banding Tools for Insulated Oil Lines
Pin Swadging Tool
Flush Cutter, Cable Cutter, Coax Tool, Soft Plier
Offset (Joggle) Vicegrips, Flange Roller Vicegrip
Fluting Pliers
HVLP Paint Spray Gun and Turbine Compressor
Telescopic Gauge Set
Tight Space Rivet Tool - Long Shaft
Rivet Nut Plate Hole Locator
...
Helicoil - Thread Chaser
Tube Flaring Tool for Aircraft Fuel Lines
De-gaussing Coil
Flying Your Own Wings - Chris Hientz
Bore Scope (Missing !!!)
|
Dymo Programmable Labeller
Bucking Bars (Assorted)
AN Alum. Fittings (in 42 drawer cabinet)
Paint Filters and Masking Paper
Avery Tools 9350
Safety Wire & Pliers ( .032 and .041)
2 Rivet Squeezers with Mandrills (1, 1.5, 2, 4")
Pneumatic Rivet Gun (Souix Tool 270A) 4x Spar
Cleco Tools (2)
Drill Guide for Bolt Heads (7 sizes + bits)
Tight Fit Drill Kit
Tubing Bender Tools (Fuel Lines)
Beading Tool
Deflection Gauge - Magnetic Base
Molex Pin Extractors and Crimper Accessories
Snap Ring Tool Set
Wire Strippers and Crimpers - Various
Paladin Pin Crimper for Sub-D connectors
Offset Metal Shears - Left, Right and Straight
Misc. Rivet Nut Plates
Terminal Tool
Cotter Pin Puller and Hole De-burring Tool
Sheridan Chip Chaser
...
Helicoil - Inserts (Various)
Fuel Injector Test Kit
Compression Tester
Rivet Cutter
...
|
Spray Guns and Accessories
AN Solid Rivets (in 42 drawer cabinet)
AN Misc. Hardware (in 42 drawer cabinet)
Paint Respirator
Koul Tools P/N 468 for Size 2, 4, 6, 8, and 10
Rivet alignment tapes and misc. for 20" press
Rivet Cutter
Pneumatic Drill (Rand)
Rivet Spacer, Gauges & Hole Finder/ Duplicator
Quad Driver/ Drill Driver (for Wood?)
Countersink Bits and Stops (misc.)
Cutting and Flaring Tools (Fuel Lines)
Clamping Vice-grips - 8 types
Perpendicular Drill Guide for Tubing/Pipe
Nico Press Tool
Screw Driver Set - Slot and Phillips
Offset Wheel Tools
C5 Pipe Crimper (thin gauge)
Pneumatic Rivet Squeezer
Small Gear Puller
Misc. Vice-grip Tools
Washer Wrenches
...
...
Cable Tension Gauge
CarbMate Balancer for Rotax912
Greenlee Panel Punch for 2.25 and 3.125 in.
Fabric Irons
...
|
